RRB ALP CBT 2 exam is the second stage computer-based test for the selection of Assistant Loco Pilots (ALP) and Technicians in the Indian Railways by Railway Recruitment Board. Aspirants who qualify the CBT-1 will be shortlisted for CBT-2. The CBT-2 will consist of two sections: Part A and Part B. Part B will be of qualifying nature consists of relevant technical question only. whereas the marks of Part A will calculated for final merit list preparation.
RRB ALP CBT 2 Exam Pattern
Section
Content
No of Question
Duration
PART A
Mathematics, General Intelligence & Reasoning, Basic Science & Engineering, General Awareness on Current Affairs.
100
90 Mins
PART B
Relevant Trade:- Mechanical Engineering-Fitter / Mechanic Motor Vehicle / Tractor Mechanic / Mechanic Diesel / Turner / Machinist / Refrigeration and Air Conditioning Mechanic/ Heat Engine /Millwright Maintenance Mechanic Electrical Engineering-Electrician / Instrument Mechanic / Wiremen/Winder(Armature) / Refrigeration and Air Conditioning Mechanic Electronics Engineering-Electronics Mechanic / Mechanic Radio & TV Automobile Engineering-Mechanic Motor Vehicle / Tractor Mechanic / Mechanic Diesel / Heat Engine / Refrigeration and Air Conditioning Mechanic
75
60 Mins
Total Questions and Marks
175
120 Mins
RRB ALP Exam Pattern – CBT 2
Important points to be remember-
The minimum qualifying marks for CBT 2 Part B are 35% i.e. 75×35% = 26.25out of 75 for all candidates irrespective of the category.
1/3rd marks shall be deducted for each wrong answer.
No Marks deducted for unattempted question.
Here we uploaded RRB CBT 2 (2018 Requitement) ALL Previous year TECHNICAL Question Paper related to Mechanical Engineering one by one. As we know every aspirants wanted previous year questions for clearing concept and to know the question pattern but for that a lots of time wasted on internet ultimately got nothing fruitful. Even after if anyone got the question paper that also Charged by big website or coaching center. Although that is small amount for them but that is HUGE Amount for students coming from Rural place OF India. So here we decided to give it completely FREE OF COST.
All questions are taken from Original Answer key given by RRB. YANTHRIST is NOT associated with Railway Recruitment Board(RRB) or Indian Railways. we try our best to provide the same questions, if any Questions found incorrect we really sorry for that, please give us your valuable feedback so that we can Improve ourselves to give you better content in future.
RRB ALP CBT 2 FITTER Question with Answer of 21 Jan 2019 Shift 1
Results
Congratulations..!!You clear CBT 2 PART B FITTER EXAM in first attempt that’s Amazing. Today you go one step ahead to your Goal.If you are satisfied with our work then share it in your Facebook or WhatsApp study group or with your 5 friends who preparing for RRB Exam and take a screenshot & send it to admin@yanthrist.com And Our Team will send you RRB ALP All Previous year’s GENERAL SCIENCE Question at FREE OF COST.
Related
Congratulations for your attempt, but you left behind to qualify exam by a little marks. That’s completely Ok, One failure can’t decide your ability.
If you are satisfied with our work then share it in your Facebook or WhatsApp study group or with your 5 friends who preparing for RRB Exam and take a screenshot & send it to admin@yanthrist.com And Our Team will send you RRB ALP All Previous year’s GENERAL SCIENCE Question at FREE OF COST.
Related
#1. To hold cutting tools like drills and reamers in a lathe machine ____ is used.
#2. Identify the type of bolt shown in the given image
#3. Which material is used to make power hacksaw blade?
#4. Which of the following is fitted on top of the compound rest of a lathe?
#5. Which type of belt is used when the distance between the shafts is too short (<1 metre distance between drives)?
#6. Which of the following types of gear set is used to change rotary into linear movement and vice versa?
#7. Which of the following gauge is used to check the wire diameter?
#8. What is the purpose of a globe valve in a pipeline?
#9. Which of the following welding process uses carbon dioxide?
#10. Which of the following file is commonly used for finishing inside the teeth of gear wheel?
#11. What is the most commonly used standard length of a feeler gauge blade?
#12. What is the purpose of an idler gear used in a gear train?
#13. What is the color of oxygen gas cylinder?
#14. Which of the following compass is used to scribe a circle or an arc with a large diameter?
#15. The type of thread used in leadscrew of a lathe is
#16. Which of the following is not a conventional type of welding process?
#17. Which of the following is not a type of comparator?
#18. ______ is the process of case hardening in which the outer layer is made hard by increasing amount of carbon.
#19. Find the tap drill size, if major dia is 10mm and pitch is 1.5 mm.
#20. Conventionally which type of surface is produced by the turning operation in a lathe machine?
#21. Which of the following gauge is used to determine the pitch of a thread?
#22. The property of a metal to draw it into thin sheets is termed as:
#23. In the hole basis system, the hole is kept constant and the size of the _______ is varied to get the desired fit.
#24. A feeler gauge is used for
#25. The surface connecting crest and root of a thread as:
#26. Jigs are available for:
#27. The number of fundamental tolerances in the Indian Standard system are:
#28. If you want to drill a hole in a switch board then you will use a_______.
#29. What is the cross sectional size of a slip gauge?
#30. Which of the following is used to block the pipe at one end?
#31. Which of the following lapping abrasives is used for obtaining high quality finish?
#32. Which one of the following belt materials can with stand acidic and wet conditions?
#33. What is the least count of a vernier bevel protractor?
#34. What is the purpose of a non-return valve in a water pipe line?
#35. Which hand tool is used to form internal thread in a hole?
#36. The process of enlarging a hole size and enhancing its surface finish is known as_________.
#37. Zinc coated iron is known as:
#38. What is the accuracy of a vernier height gauge?
#39. What is the included angle of a lathe dead center?
#40. Tab washers are used for:
#41. Drill chucks are fitted on the drilling machine spindle by means of_____
#42. The measuring faces of the slip gauges are finished by________.
#43. Why surface plate is used for marking?
#44. The difference between the maximum limit of size and minimum limit of size in assembling a product is known as______.
#45. Plain ring gauges are used to check:
#46. Which of the following is not used to connect two shafts together in order to transmit power?
#47. Which one of the following maintenance is the most effective?
#48. Which material is used to make races of ball bearings?
#49. Which one of the following material is used to make a tip of a centre punch?
#50. Which nut can be easily operated by the thumb and finger?
#51. Which of the following is a multi point cutting tool?
#52. What does a vernier bevel protractor measure?
#53. Which material is used to make a file?
#54. Shearing the sheet into two or more is known as
#55. The length of a sine bar is the distance between ______
#56. Identify the standard form of pipe thread from the following:
#57. Which of the following is not a type of common thread fastener?
#58. The dimension of a nut is expressed in terms of:
#59. How can aluminium be identified visually in a group of work pieces made of aluminium, brass, copper and mild steel?
#60. Which of the following material is the outer part of a holding jaw in a bench vice made up of?
#61. Which of the following is used to hold pipes between 50-150 mm dia?
#62. In which of the following locking nuts is a slot cut halfway across the nut?
#63. When the size of a smallest hole is bigger than the size of the biggest shaft, then it is called a/an ______.
#64. Which of the following instrument is not used to measure angles?
#65. Which type of thread is used in screw jack?
#66. What is a metal's ability to withstand wear, abrasion and penetration called?
#67. Which of the following is the temperature at which lubricant will start to flow when poured?
#68. Which among the following is the use of a GO gauge?
#69. The major purpose of using go and no go gauge is to use it as a____.
#70. The least count of steel rule is________.
#71. Twist drills are made up of which of the following materials?
#72. Which of the following marking media is used for filed or machine finished surface?
#73. Which of the following process is used to super finish a bore in ferrous metal?
#74. What is the %age of tin in soft solder?
#75. The 'ring oiling system' is also known as______
