RRB ALP CBT 2 FITTER (21 Jan 2019 Shift 2) Question With Answer

Leave a Comment / RRB ALP/Technician / By

RRB ALP CBT 2 exam is the second stage computer-based test for the selection of Assistant Loco Pilots (ALP) and Technicians in the Indian Railways by Railway Recruitment Board. Aspirants who qualify the CBT-1 will be shortlisted for CBT-2. The CBT-2 will consist of two sections: Part A and Part B. Part B will be of qualifying nature consists of relevant technical question only. whereas the marks of Part A will calculated for final merit list preparation.

RRB ALP FITTER QUESTION 21 JAN 2019 SHIFT 2

RRB ALP CBT 2 Exam Pattern

SectionContentNo of QuestionDuration
PART AMathematics,
General Intelligence & Reasoning,
Basic Science & Engineering,
General Awareness on Current Affairs.		10090 Mins
PART BRelevant Trade:-
Mechanical Engineering- Fitter / Mechanic Motor Vehicle / Tractor Mechanic / Mechanic Diesel / Turner / Machinist / Refrigeration and Air Conditioning Mechanic/ Heat Engine /Millwright Maintenance Mechanic
Electrical Engineering- Electrician / Instrument Mechanic / Wiremen/Winder(Armature) / Refrigeration and Air Conditioning Mechanic
Electronics Engineering- Electronics Mechanic / Mechanic Radio & TV
Automobile Engineering- Mechanic Motor Vehicle / Tractor Mechanic / Mechanic Diesel / Heat Engine / Refrigeration and Air Conditioning Mechanic		7560 Mins
Total Questions and Marks175120 Mins
RRB ALP Exam Pattern – CBT 2

Important points to be remember-

  • The minimum qualifying marks for CBT 2 Part B are 35% i.e. 75×35% = 26.25 out of 75 for all candidates irrespective of the category.
  • 1/3rd marks shall be deducted for each wrong answer.
  • No Marks deducted for unattempted question.

Here we uploaded RRB CBT 2 (2018 Requitement) ALL Previous year TECHNICAL Question Paper related to Mechanical Engineering one by one. As we know every aspirants wanted previous year questions for clearing concept and to know the question pattern but for that a lots of time wasted on internet ultimately got nothing fruitful. Even after if anyone got the question paper that also Charged by big website or coaching center. Although that is small amount for them but that is HUGE Amount for students coming from Rural place OF India. So here we decided to give it completely FREE OF COST.

NAME OF TRADESPECIFIC SHIFT
FITTERRRB ALP CBT 2 FITTER (21 Jan 2019 Shift 1) Question With Answer
RRB ALP CBT 2 FITTER (21 Jan 2019 Shift 2) Question With Answer
Mechanic Diesel To Be Uploaded Very soon
HEAT ENGINETo Be Uploaded Very soon

All questions are taken from Original Answer key given by RRB. YANTHRIST is NOT associated with Railway Recruitment Board(RRB) or Indian Railways. we try our best to provide the same questions, if any Questions found incorrect we really sorry for that, please give us your valuable feedback so that we can Improve ourselves to give you better content in future.

RRB ALP CBT 2 FITTER Question with Answer of 21 Jan 2019 Shift 2

Results

Congratulations..!!You clear CBT 2 PART B FITTER EXAM in first attempt that’s Amazing. Today you go one step ahead to your Goal.If you are satisfied with our work then share it in your Facebook or WhatsApp study group or with your 5 friends who preparing for RRB Exam and take a screenshot & send it to admin@yanthrist.com And Our Team will send you RRB ALP All Previous year’s GENERAL SCIENCE Question at FREE OF COST.

Congratulations for your attempt, but you left behind to qualify exam by a little marks. That’s completely Ok, One failure can’t decide your ability.

If you are satisfied with our work then share it in your Facebook or WhatsApp study group or with your 5 friends who preparing for RRB Exam and take a screenshot & send it to admin@yanthrist.com And Our Team will send you RRB ALP All Previous year’s GENERAL SCIENCE Question at FREE OF COST.

Share your score!
Tweet your score!
Share to other

#1. Which part of a lathe machine is involved for taper turning?

#2. ________ is a mechanical property of a metal.

#3. Least count of Vernier depth gauge _______

#4. The point angle of a scriber is ____.

#5. The least count of a vernier caliper is ______.

#6. The process of enlarging the hole size and enhancing its surface finish is known as_______.

#7. Which is the possible cause when a twist drill produces a rough hole on the job?

#8. Jigs are NOT used in which of the following operations?

#9. Which gauge is used to check the diameter of a hole?

Inside micrometer bore gauge etc. are used to check diameter of hole.

#10. The point angle of a drill bit is _______.

#11. G.I pipes are coated with ________

#12. The process of cutting thread by tap in a ground hole is called:

#13. Which type of bearing is used in a crankshaft ?

#14. Which of the following is NOT a conventional type of welding process?

#15. Which of the following metal is used in a ‘B’ grade V-block?

#16. The viscosity of petroleum oil for hydraulic lifts ______

#17. The upper part of a chisel (head) is chamfered to an angle of ______.

#18. The dimension of a nut is expressed in terms of:

#19. Go No Go gauge is a type of_______.

#20. The minimum that can be correctly read with a vernier calliper is called:

#21. Shearing the sheet into two pieces or more is known as_______

#22. Which among these is common to both the parts of matching pair?

#23. What is attached to a dial face for the rapid checking of parts?

#24. V blocks are available in grades of______.

#25. A master height gauge is used to measure _______.

#26. Bearings are generally made of _______.

#27. Honing is used for the finishing of a/an_______.

#28. Drill chucks are held on the machine spindle by means of a/an:

#29. which marking medium is used to draw clear and sharp lines?

#30. The box nut of a bench vice is made up of

#31. The process of filing from one end to another end in one stroke is called:

#32. Slots are provided in an angle plate for ______.

#33. Which of the following instruments is NOT used to measure angles?

#34. _________is a semi-circular key used for transmitting light torque.

#35. A rog bolt is a type of ________.

This is a foundation bolt to keep the heavy machinery on its position.

#36. Which nut can be easily operated by the thumb and a finger?

#37. Which metal is NOT suitable for lapping

#38. Which process is used to convert mild steel to high carbon steel?

#39. When the size of the smallest hole is more than the size of the biggest shaft, then it is called a/an_____.

#40. The value of each main-scale division of a vernier bevel protractor is

#41. In which process the machined component is neaten and smooth from rough edges or ridges manually?

#42. Which stake is used to make a conical or bevelled funnel?

#43. Which among the following is NOT a Factor for the section of cutting speed and feed rate for reaming a hole with a machine reamer?

#44. An outside micrometer has a negative error. The correct reading can be taken by

#45. A hollow punch is used for punching holes in______.

#46. The mallet is generally made up of_______.

#47. Which drill is used for large-batch production?

#48. The hardness of steel increases:

#49. which of the following is also known as a tool rest?

#50. The property of metals to draw into thin sheets is called ______.

#51. What is the angle of ACME thread?

#52. A fixture is used to _______.

#53. Tensile strength of an alloy steel can be improved using _______

#54. The algebraic difference between the upper limit and the lower limit is called_______.

#55. In which of the following forging operations, no special die is used?

#56. Which nut is a hexagonal nut with a washer?

#57. From which material is a hammer made?

#58. By which forging method are bolts produced ?

#59. The toughness in steel increases and the brittleness by a heat treatment operation called _____.

#60. Which type of surface is produced by the turning operation in a lathe machine?

#61. The property of a metal by which it can be drawn into wires is called_____.

#62. Which of the following is an example of fusion welding ?

#63. Which of the following is a type of direct measuring instrument?

#64. The alloy of copper and zinc is known as _______

#65. Cast iron can be easily obtained by processing the ore in a _______.

#66. The least count of a metric micrometer is ________ in mm.

#67. Which bolt is commonly used in bearings for shafts?

#68. The gap between two matching parts is measured by a _______

#69. In a pneumatic system, an AND gate is known as______

#70. Which of the following is the appropriate drill size for an M10 tap?

#71. Which of the following is NOT a type of comparator?

#72. Which type of maintenance is the most effective?

#73. If you want to make a hole in a switchboard, then you will use a _______.

#74. Which rivet is used in light sheet-metal work?

#75. The minimum measurement that can be read with the help of a steel rule is _______.

Finish

Related Posts

Leave a Comment

Your email address will not be published. Required fields are marked *

Subscribe
Subscribe
Scroll to Top